Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Blog Article

Do not underestimate the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the person ahead can not be located, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should initially validate that the tons is secure and trustworthy.
4. The start needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be slanted backward. .
2. Do not lift the fork expensive when driving. When going into and leaving the work site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be increased expensive, which will impact the security of the forklift. .
3. After unloading, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the load must not block the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading items, the range between both Electric Forklift Truck for Warehouse forks must be changed as required to make the lots of the two forks well balanced and not skewed, and one side of the item need to protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or items. The lots should be supported with marginal back tilt of the gantry so that the tons does not move in reverse. The mast can be slanted ahead a little when the tons is decreased to enable easy positioning of the tons and removal of the forks. .
6. It is restricted to fork products at broadband and hit hard things with the fork head. .
7. When the forklift is working, it is prohibited for people to loaf the fork, so regarding prevent the collapse of the goods and harm individuals. .
8. Overwhelming is prohibited, and it is restricted to utilize forks to raise personnel to take part in high-altitude operations to avoid high-altitude dropping mishaps. .
9. It is not enabled to use the brake inertia to slide, place, round or roll things. .
10. It is not permitted to utilize forks to select, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork structure.
2. Draw the emergency brake take care of to dead or depress the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for unique conditions, such as the vehicle driver does not leave the lorry's line of sight and does not go beyond 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be added.
2. Inspect the security performance of starting, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. During the operation of the forklift, check whether the pressure and temperature level are typical.
5. After the forklift is running, the external leak must additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the car;.
2. When you experience someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope ought to be sluggish and uniform, and no activating the slope is allowed.
7. Do not drive across the gradient. When the gradient is above 10%, the vehicle needs to be driven in reverse when going downhill;.
8. When the forklift workers bring the goods and move on, if they encounter big or hefty items and most likely to the driver's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" ought to be complied with in the procedure.
1. Single fork procedure is not enabled.
2. It is not permitted to raise the goods for long distance driving.
3. It is not permitted to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not permitted to make use of inertia pressure to get the goods.
6. It is not permitted to utilize braking pressure to expatriation round or easy-to-roll things.
7. It is not enabled to bring people to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Car park is not allowed under the following conditions.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the roadway, the opposite side of the area with the same length as the Electric Forklift Truck for Warehouse challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844